0**2041⑨Oil Port Thread Specification or Special SpecificationM6W***30017250⑤NOMINAL GAS VOLUME ※3⑥SPECIFICATION FOR TOP CAP & GAS CHARGING SIDEA-Standard Dynac Valve (G thread)②BLADDER COMPOUNDN-Standard Nitrile Rubber (NBR) H-Nitrile Rubber for High Temp. Use (H.NBR)L-Nitrile Rubber for Low Temp. Use (L.NBR)F-Butyl Rubber (IIR)E-Ethylene Propylene Rubber (EPDM)C-Chloroprene Rubber (CR)G-Epichlorohydrin Rubber (CHC)V-Fluorine Rubber (FKM)⑨0⑨6⑨M⑧C⑦A⑥A--⑤0⑤2⑤L--④P④M④3④2－－－－－－－－－⑧SPECIFICATION OF SHELL / SURFACE TREATMENT③SERIES④Maximum Allowable Working Pressure ※22 MPa, 21 MPa, 23 MPa, 25 MPa, 35 MPa, 45 MPa, 49.1 MPa, 50 MPa①APPLICABLE INSPECTION/STANDARDH-JAPAN High Pressure Gas Safety Law (Japan)M-U.S.A. ASMER-EUROPE PED (2014/68/EU)D-CHINA N-NACOL (Manufacturer’s) Inspection※1 Some models may neither be covered by the standards nor supported by NACOL (Manufacturer).※3 For 10L, only the small diameter U ⑦SPECIFICATION FOR OIL PORT SIDEA-Standard Carbon SteelE-High FlowY-Super High FloweMaximum AllowablepWorking PressureahSAAAAAAAAAAAAAAAAAAAAA49.1(50)※9A49.1(50)※9A49.1(50)※9A49.1(50)※9A49.1(50)※945StandardItem Numberseries can be selected.exceeds 35 MPa/350 bar.H Series, N Series, U Series10 L, 20 L, 29 L, 30 L, 40 L, 50 L, 60 LFor 45/49.1/50 MPa/Top Cap Two D-Pieces Type/Dynac Valve (G thread)Q-SG Valve + Safety Valve + Pressure Gauge ※4 R-SG Valve + Fuse Plug + Pressure Gauge ※4※4 Q and R cannot be selected if the pressure For Special Specifications or High flow Manifold Type or Screen TypeX-Nominal GasVolumeL20293040506020293040506030405060304050602030405060MPa2323232323233535353535353535353545454545peel off, such as phosphate ester based fluids and water glycol fluids.DoMass※6mmkgmmmm852+17859+17668267.4840001,078+17267.41,071+178871110267.41,097+1701,104+17913114001,343+17267.41,336+1701,15214301,641+17267.41,634+1701,45017901,828+17267.41,821+1701,637201865+23872+23161298.56710001,111+23298.51,104+23910211001,117+23298.51,110+23212916001,332+23298.51,325+2301,131262298.51,647+2301,654+2333101,45301,792+23298.51,785+2301,59136301,117+23298.51,110+23218916001,332+23298.51,325+2301,131265298.51,647+2301,654+2333701,453298.51,785+2301,792+2301,591372298.51,110+232189160298.51,325+232651,1310298.51,647+233371,4530298.51,785+233721,5910865+23298.51646710298.51,110+232179160298.51,325+232661,1310298.51,647+233371,4530298.51,785+233721,5910LABCFHGSPECIFICATION OF SHELLInside SurfaceZinc Phosphate TreatmentZinc Phosphate TreatmentPetroleum Based Hydraulic Oil & Other FluidZinc Phosphate TreatmentZinc Phosphate TreatmentC-D-A-※5 B-※5N-W-X-※5 Inner surface coating is unsuitable when using fire resistant fluids that may cause the paint to Standard Material(Carbon Steel)Zinc Phosphate TreatmentZinc Phosphate TreatmentSpecial SpecificationsOil Port Connection Thread Type and Thread SizeOil Port Connection Diameter of FlangeSpecial Specifications35 MPa for China, Shell Material SpecialOil Port Connection Diameter of Flange 100 AHigh Flow Manifold Type 23 MPaScreen TypeA’mmmmmmmmmmmmmm7777777777777777777777777777777777777777777777777715715715715715715716416416416416416416416416416416416416416416416416416416485858585858595959595959595959595959595959595959595Outside SurfacePaint CoatingPaint CoatingPaint CoatingPaint CoatingPaint CoatingSERVICE FLUIDWater-Glycol FluidPetroleum Based Hydraulic Oil & Other FluidZinc Phosphate TreatmentPetroleum Based Hydraulic Oil & Other FluidPetroleum Based Hydraulic Oil & Other FluidWater-Glycol FluidD190HN-H23MP-L20-AACM6090N-H23MP-L29-AACM6090HN-H23MP-L30-AACM6090HN-H23MP-L40-AACM6090HN-H23MP-L50-AACM6090HN-H23MP-L60-AACM6090HN-N35MP-L20-AACM6090N-N35MP-L29-AACM6090HN-N35MP-L30-AACM6090HN-N35MP-L40-AACM6090HN-N35MP-L50-AACM6090HN-N35MP-L60-AACM6090N-N35MP-L30-AAX03290N-N35MP-L40-AAX03290N-N35MP-L50-AAX03290N-N35MP-L60-AAX03290N-N45MP-L30-DACM6090N-N45MP-L40-DACM6090N-N45MP-L50-DACM6090N-N45MP-L60-DACM6090HN-N49.1-L20-DACM6090HN-N49.1-L30-DACM6090HN-N49.1-L40-DACM6090HN-N49.1-L50-DACM6090HN-N49.1-L60-DACM60※2 For the accumulator with P.E.D. inspection, the maximum allowable working pressure designated in each item number is in units of bar, not MPa (e.g. 23 MP → 230 B).※6 Weight may vary depending on applicable inspections and standards.※7 Dimensions without tolerance indication are for reference. Please confirm the dimensions with the actual product.※8 Maximum oil flow rate available under certain conditions.※9 For products certified according to NACOL (Manufacturer's) Inspection, Japan, the maximum allowable working pressure is 50 MPa.※10 The Chinese inspection products with maximum working pressure of 23 MPa and nominal gas volume of 40 L and 60 L differ in overall length from the above.3265455718101,1081,2953205595657801,1021,2405657801,1021,2405657801,1021,2403205657801,1021,240250250250400700700250250250400700700250400700700250400700700250250400700700Explanation of Item Number (For details, please refer to p. 27-30.)①②-③HN-HDimensional Table
元のページ ../index.html#46